INTERPLATER HD85 135 THERMAL PDF
Interplater hd85 thermal pdf. Thermal analysis and design enae d principles of space systems design u n i v e r s i t y o f maryland nonideal radiative. Service Manual + 68/85 Plate Processor InterPlater 85/ HD Polymer Service manual Plate Processor+ 68/85 .. Cleaning of developer heating element. Thermal Plate Processor Raptor 85/ Interplater HD 85 G&J used/refurbished. Glunz Jensen Interplater Plate Processor Model Perfect Condition.
|Published (Last):||5 January 2005|
|PDF File Size:||20.59 Mb|
|ePub File Size:||15.39 Mb|
|Price:||Free* [*Free Regsitration Required]|
Configuration and settings Additional configuration might be necessary to suit the individual customer needs.
When mounting upper roller insert the roller key between the upper roller and the lower roller as shown 3. Processor must stop when the switch is deactivated.
InterPlater 85/ HD Service Manual |
interplqter Functional description General Processor sections The processor contains six major sections, each performing a basic function to change the exposed plate into a fully developed and dry plate, ready for handling see illustration below.
Plates and chemicals are very sensitive materials and correct storage is vital to obtain a satisfactory production result. They comprise the different parts necessary to make the installation and some key interplate as spareparts. Other fuses for the various functions are located in the electronics cabinet behind the upper right fender. Adjustment of the lid switches may be needed after leveling of the processor.
For cleaning and maintenance subjects see the processor user manual. The roller 5 makes sure of proper contact between brush and plate.
Note the position of the outlet nozzle 5. See the table on the following page for a description of the fuses. Install the rollers as shown on the label. Preparations See the illustration on the following page. Pressure is adjusted as shown on the illustration below.
When the cable is not in use, please reel it and secure the receptacle away from liquid and readily accessible areas.
Interplater hd85 135 thermal pdf
The rollers 12 at the developer tank exit squeeze any residual chemicals off the plate. The exit roller pair 21 takes the plate when dry and leads it out of the processor. The processor has been either off or in sleep mode for more than 72 tuermal.
Long-handled bottle brush and thin wire i. Select NO otherwise the system will start replenishing based on how many hours the machine has been switch off since the machine has been packed. Also be aware that the processor’s heaters and motors will be in operation during the initial startup if you have overridden the machine’s safety functions.
For cleaning of rollers, guides, tank walls, and all surfaces, especially the exit table and the feed table if fitted. Loosen the screws 1 and adjust the actuator 2 sidewards until it fits smoothly 3 into the switch 4. Solar thermal energy an industry report solar thermal technology on an industrial scale the sun is our source our sun produces ,,,, watts of energy every second and the belief is that it will last for another 5 billion years.
The pre-heat section rollers 1 transport the plate through the pre-heat section. Also the developer top-up function automatically adds fresh developer to the developer section when low level is detected. Interplater hd thermal inyerplater a discontinued product. Procedure of adjustment See illustration on the following page.
The troubleshooting guide is divided into two sections: The processor will initialize and then automatically switch to Ready mode. No wash water recirculation. The installation procedure is described later in this manual. The parameters to be configured are: Contact your local supplier for information about storage requirements for plates and chemicals. Alternatively a forklift truck is recommended. Batteries No batteries in this equipment. If this does not help, take the pump apart and clean both of the small valves in warm water.
Mounting of the feed table is described in the manual for the feed table kit. Cable for connection to a stacker is placed underneath the dryer section. Do not let is slip down behind the rear panel. Notes, cautions, and warnings! Installation and adjustment of brush rollers are described in chapter 3 in the processor service manual.
InterPlater 85/ HD Thermal | Glunz & Jensen
T y che ort rol cle 1. Please note that where this label appears on the processor, electrical shock hazard still exists when the main switch is turned off. Connect conductors in power cord to terminals: S8 type essor X proc XX.
If however any extra features like level sensors for replenish containers etc. Incorrect storage may very well result in unsatisfactory processing quality etc. Maintenance General Thermall section contains special service information such as fuse list and roller adjusting procedures etc. For personal protection Lint-free cloth, sponge and soft brush. Lead the cable as shown below.